Free UK delivery over £250Family run since 1948Showrooms in Halifax & Bradford

Choosing the fitting

Wall Lights Guide: Heights, Spacing, Switching and Plug-in Options

By the Harrison Lighting team · Updated 16 November 2026

Wall lights do what a single ceiling light can't. They put light at eye level, soften shadows, make a room feel wider and give you a lower, warmer setting for the evening. Getting them right is mostly about height, spacing and how they are switched, and those are decided before the plaster goes back on.

Where wall lights work best

How high to fix wall lights

The aim is to see the glow, not the bulb. That means fixing the light above the eye level of the people using the room, and keeping the height consistent so a row of lights reads as a line.

RoomTypical height of the light from the floorWhy
Living roomAbout 1.5 to 1.7 mAbove seated eye level, so you don't look into the shade from the sofa
Hallway and landingAbout 1.6 to 1.8 mAbove standing eye level and clear of shoulders in a narrow space
BedsideAbout 1.2 to 1.5 m, depending on bed heightLow enough to read by when sitting up, high enough to clear your head
Bathroom mirrorEither side at about face height, or just above the mirrorLights your face from the front instead of from above

These are typical figures, not rules. Ceiling height, the size of the fitting and whether it points up or down all change the answer. Uplighters can go a little higher; a fitting with a deep shade may sit a little lower. On stairs, keep the lights at a consistent height above the line of the treads so they follow the slope.

For bedside wall lights, sit up in bed with a book and have someone hold the light where it would go. You want the light falling on the page from slightly behind your shoulder, and an adjustable arm helps if two people read different ways.

How far apart to space them

  • In a run along a hall or a long wall, roughly 2.5 to 3 m apart gives even pools of light without dark gaps.
  • In pairs, centre them on the feature (fireplace, mirror, bed or sofa) rather than the wall.
  • Keep a light at least a hand's width or two from a corner, so the light spreads onto both walls rather than hitting the return.
  • Think about furniture first. A wall light that ends up behind a tall bookcase or a wardrobe door is wasted.

Up, down or both?

Uplighters wash the ceiling and make a room feel taller and softer. Downlighters pool light onto a table, a picture or a path. Up-and-down fittings throw light both ways and make a feature of the wall itself, which looks good on textured walls and brick. Shaded wall lights give the softest, most even glow. Picture lights are a separate type, mounted above a frame to light the picture itself.

Switched, unswitched or plug-in

Unswitched (controlled from the wall)

Most hard-wired wall lights have no switch of their own and come on from a wall switch, often with the other wall lights in the room. This is the neatest result and lets you put them all on one dimmer.

Switched (a switch on the fitting)

Switched wall lights have a rocker, push or pull-cord switch on the fitting. They are useful beside a bed, so each person can turn their own light off without getting up. They are still wired in, and the circuit can be on a wall switch as well.

Plug-in wall lights

Plug-in wall lights are fixed to the wall and run on a flex to a normal socket, usually with an in-line switch. No electrician is needed, which makes them a good choice for renters or where chasing the wall isn't practical. Plan where the flex runs: straight down to a socket looks tidier than a diagonal, and cable covers painted to match the wall make it almost disappear.

Wiring and the rules

Hard-wired wall lights are usually fed from the lighting circuit, which means channelling cable into the wall, so it is best done when you are decorating. Extending an existing lighting circuit is not usually notifiable under Part P in England, but a new circuit is, and so is work in a bathroom within the zones. Use a registered electrician, who will also check the wall fixing and the box behind the light. Your electrician will confirm what applies.

Bulbs and dimming

Many wall lights take E14 candle bulbs or G9 capsules, and some have built-in LEDs. Check the cap and the maximum wattage on the product page, and our bulbs and caps guide explains the differences. For a living room, warm white (2700K) bulbs on a dimmer give the evening light most people want. If you plan to dim, check the bulbs or fitting are dimmable and the dimmer suits LED, as covered in LED lighting explained.

Before you order

  • Decide the height and mark it on the wall with tape. Check from the sofa, the bed or the doorway.
  • Measure how far the fitting projects from the wall, especially in a narrow hall or beside a door.
  • Choose switched, unswitched or plug-in, and make sure the electrician knows before cables go in.
  • Check the bulb cap and whether bulbs are included.
  • In a bathroom, check the IP rating suits the zone.
  • Buy matching pairs and runs together, so finishes and glass match.

Need a hand choosing?

If you are unsure about a size, a height or whether a light suits your room, call our advice line on 01422 363525. Better still, bring your measurements (and a photo of the room) to our Halifax showroom or our Bradford showroom (Bradford line 01274 731333) and see the fittings lit. You can also book an appointment so someone is free to go through it with you.

Questions people ask

How high should wall lights be from the floor?

In living rooms, usually about 1.5 to 1.7 m; in hallways about 1.6 to 1.8 m. The aim is to fix them above eye level so you see the glow, not the bulb, and to keep the same height across the room.

How high should bedside wall lights be?

Typically about 1.2 to 1.5 m from the floor, depending on the bed. Sit up in bed and check the light falls on your book from just behind your shoulder before the electrician fixes it.

What are switched wall lights?

Switched wall lights have their own switch on the fitting, such as a rocker or pull cord. Unswitched ones are turned on and off from the wall switch.

Do plug-in wall lights need an electrician?

No. They fix to the wall and plug into a normal socket, usually with an in-line switch on the flex. You only need to plan a tidy route for the cable.

How far apart should wall lights be?

In a run, roughly 2.5 to 3 m apart. In pairs, centre them on the fireplace, mirror, bed or sofa they frame rather than on the wall.

Can I put wall lights on a dimmer?

Yes, if the bulbs or the fitting are dimmable and the dimmer suits LED. Putting all the wall lights in a room on one dimmer gives an easy evening setting.

Related guides