Choosing the fitting
Table and Floor Lamps Guide: Sizes, Shades and Placement
By the Harrison Lighting team · Updated 16 November 2026
Table and floor lamps are the easiest lights to add and the quickest way to make a room feel lived in. They put light low down, where people sit and read, and they let you turn the big ceiling light off in the evening. The main things to get right are the height, the shade and where the plug goes.
What each lamp is for
- Table lamps give a soft pool of light on side tables, consoles, desks and windowsills. Browse our table lamps.
- Bedside lamps are table lamps sized for reading in bed and switching off without getting up.
- Floor lamps light a corner or a reading chair where there is no table. Browse our floor lamps.
- Reading and task floor lamps have an adjustable head or arm to aim light onto a book or a craft.
- Uplighter floor lamps bounce light off the ceiling, which helps in rooms with low ceilings.
- Mother-and-child lamps combine an uplighter with a small reading arm in one stand.
Getting the height right
The rule that matters most: you want to see the glow of the shade, not the bulb. That depends on where your eyes are when you use the lamp.
| Lamp | Where the bottom of the shade should be |
|---|---|
| Table lamp beside a sofa or chair | Roughly at eye level when seated, so the bulb is hidden but light falls across your lap |
| Bedside lamp | Near chin height when you sit up in bed |
| Reading floor lamp | Just above shoulder height when seated, placed beside or slightly behind the chair |
| Console or hall table lamp | Above standing eye level is less important; choose a lamp in proportion with the table and any mirror above it |
Measure the table too. A tall lamp on a tall side table can put the shade well above your head, and a small lamp on a low table may light only the table top. Lamp height plus table height is the figure that counts.
Choosing the right shade
A good shade hides the bulb and bulb holder from normal viewing angles and sends light where you need it. As a starting point:
- Make the shade diameter roughly equal to the height of the base.
- Make the shade height about two-thirds of the base height.
- Then adjust by eye. A heavy base takes a larger shade; a slender one looks better with a smaller shade.
Shade colour changes the light. White and cream linings spread more light; dark or opaque shades send it up and down only, which suits mood lighting but not reading. Gold or champagne linings warm the light.
Check how the shade fits the lamp. Most shades either sit on the lampholder with a ring sized to it, or on a harp or carrier, and the ring for a small E14 holder is smaller than for an E27 or B22 holder. The product page gives the fitting and the maximum bulb wattage. Stay within that maximum. Our lamp shades range lets you replace a tired shade or change the look of a lamp you already have.
Where to put lamps in a room
- Living rooms: a lamp at each end of the sofa, a floor lamp by the reading chair, and one more in the darkest corner. Spreading three or four lamps around the room lights it more evenly than one bright one. See the living room lighting guide.
- Bedrooms: a matching pair either side of the bed. If space is tight, consider wall lights instead; our wall lights guide covers bedside heights. See also the bedroom lighting guide.
- Hallways: a lamp on a console table makes an entrance welcoming and is a gentle light to leave on.
- Kitchens and dining rooms: a lamp on a dresser or sideboard gives a soft light for eating when the bright kitchen lights are off.
Lamps are the task and accent layers of a room. Our guide to layered lighting shows how they work with the ceiling and wall lights.
Plugs, cables and 5 amp lamp circuits
Plan lamps around your sockets. A cable across a walkway is a trip hazard, especially for older people; see our advice for older people at home. Run flexes along walls or under rugs that don't move, and avoid using long extension leads as a permanent fix.
If you are rewiring or redecorating a living room, consider a 5 amp lamp circuit. Lamps plug into small round-pin sockets, and that circuit is switched from the door (and can be dimmed) like a ceiling light. Every lamp then comes on together with one switch. It needs a registered electrician and round-pin plugs on the lamps, but it is one of the most useful upgrades in a living room.
Bulbs and colour
Most table and floor lamps take an E27 or E14 screw bulb, or a B22 bayonet. For reading, around 470 to 806 lumens (the light of an old 40 W to 60 W bulb) is plenty in a shaded lamp. Choose 2700K warm white in living rooms and bedrooms; a slightly cooler 3000K or 4000K bulb helps in a task or reading lamp. Where a lamp takes a separate bulb, we offer the right bulb with it, and you will find spares in bulbs and accessories. Our bulbs and caps guide explains caps, lumens and colour temperature.
Some lamps have built-in dimmers or touch switches. To dim a lamp with a normal switch, use a dimmable bulb with a plug-in or in-line dimmer that suits LED. LED lighting explained covers why the wrong dimmer causes flicker.
Before you order
- Measure the table or floor space and the height of the table top.
- Check the overall lamp height and the shade size against where you will sit.
- Check whether the shade is included, and what fitting it uses.
- Note the bulb cap and maximum wattage, and whether a bulb is included.
- Check the floor lamp's base diameter and weight if children or pets are about.
- Find the nearest socket, and measure the cable length.
Need a hand choosing?
If you are unsure about a size, a height or whether a light suits your room, call our advice line on 01422 363525. Better still, bring your measurements (and a photo of the room) to our Halifax showroom or our Bradford showroom (Bradford line 01274 731333) and see the fittings lit. You can also book an appointment so someone is free to go through it with you.
Questions people ask
How tall should a table lamp be?
Choose a height that puts the bottom of the shade at roughly eye level when you are seated next to it. Add the height of the table to the height of the lamp to check.
What height should a bedside lamp be?
The bottom of the shade should sit near chin height when you are sitting up in bed. That lights the page without shining in your eyes.
What size lampshade do I need for my lamp?
A good starting point is a shade diameter about equal to the base height, and a shade height about two-thirds of the base height. The shade should hide the bulb holder from normal viewing angles.
Where should a floor lamp go?
Beside or slightly behind a reading chair, with the shade just above shoulder height when seated, or in a dark corner to fill the room with light.
What is a 5 amp lamp circuit?
A circuit of small round-pin sockets controlled from a wall switch or dimmer, so all the lamps in a room come on together. It needs to be installed by a registered electrician.
What bulb should I use in a table lamp?
Check the cap on the product page, usually E27, E14 or B22. For a shaded lamp, 470 to 806 lumens in 2700K warm white suits most living rooms and bedrooms.