Free UK delivery over £250Family run since 1948Showrooms in Halifax & Bradford

Bulbs and light

Light Bulbs and Caps Guide: E27, E14, B22, G9 and GU10 Explained

By the Harrison Lighting team · Updated 16 November 2026

Most bulb mistakes come down to three things: the wrong cap, the wrong brightness or the wrong colour. This guide explains how to read each one, so the bulb you order fits first time and gives the light you expected.

Where a light takes a separate bulb, our product pages now offer the right bulb to go with it, so you can order both together. If you are replacing a bulb in a light you already own, the sections below will help you match it.

Step 1: find the cap

The cap is the end of the bulb that goes into the lampholder. The letter tells you the type (E for Edison screw, B for bayonet, G for pins) and the number is the size in millimetres. The cap is usually printed on the old bulb, on the lampholder or in the fitting's instructions and specification.

CapAlso calledWhat it looks likeWhere you find it
E27ES, Edison screwLarge screw thread, 27 mmPendants, table and floor lamps, many ceiling lights
E14SES, small Edison screwSmall screw thread, 14 mmChandeliers, wall lights, small lamps
B22BC, bayonet capTwo side lugs, push and twist, 22 mmTraditional UK pendants and lamps
B15SBC, small bayonet capSmall bayonet, 15 mmOlder chandeliers and wall lights
G9G9 capsuleSmall mains capsule with two looped pins 9 mm apartModern ceiling lights, glass and crystal fittings, wall lights
GU10GU10 spotlightTwo stubby pins with feet, push and twist, mains voltageCeiling spotlights, spot bars, downlights
GU5.3MR16Two thin straight pins 5.3 mm apart, 12 voltOlder low-voltage downlights with a transformer

Watch out for

  • GU10 and GU5.3 (MR16) look alike from the front. GU10 pins have little feet and twist in; MR16 pins are straight and push in. MR16 bulbs run at 12 volts from a transformer, and an LED MR16 only works reliably if the transformer or driver suits LED.
  • G9 and G4 are both small capsules. G4 has two straight pins and runs at 12 volts; G9 has looped pins and runs at mains voltage.
  • E27 and B22 are not interchangeable, though both are common in the UK. Cap adaptors exist, but they make the bulb sit lower or higher in a shade, so it is better to buy the right cap.

Step 2: choose the shape

The shape changes how the bulb looks in an open fitting and how well it fits inside a shade.

  • GLS: the classic pear shape, for most shades and pendants.
  • Candle: slim and pointed, for chandeliers and candle-style wall lights. Usually E14 or B15.
  • Golf ball: small and round, for small shades and wall lights.
  • Globe: a large round bulb meant to be seen, often on bare pendants.
  • Filament: LED strands that mimic old carbon filaments, often at 2200K, for clear glass and exposed bulbs.
  • Reflector (GU10, R50, R63): directs light forward in a beam, for spotlights.

Check the fitting's maximum bulb size as well as the cap. A globe will not fit inside a small shade, and a long bulb may show below the rim of a pendant shade.

Step 3: choose the brightness in lumens

Brightness is measured in lumens, not watts. Watts show how much power a bulb uses, and an LED uses far fewer watts for the same light. Use this table to match the bulb you are replacing.

Old filament bulbLED light outputTypical use
25 Wabout 250 lmDecorative lamps, candle bulbs on a chandelier
40 Wabout 470 lmTable lamps, wall lights
60 Wabout 806 lmPendants, reading lamps
75 Wabout 1,055 lmMain ceiling light in a medium room
100 Wabout 1,521 lmLarge rooms, workshops

For spotlights, compare the lumens on the box with what you have now rather than relying on a watt figure, and check the beam angle: a narrow beam (around 36 degrees or less) makes pools of light, a wider beam (60 degrees or more) spreads light more evenly.

For a whole room, a planning figure is roughly 100 to 200 lumens per square metre of floor for living rooms and bedrooms, 100 to 150 for hallways, 300 to 400 on kitchen work areas and 200 to 300 for bathrooms, with more at the mirror. Add up the bulbs in all the lights, not just the ceiling one.

Step 4: choose the colour

Colour temperatureLooks likeGood for
2200K extra warmCandlelight, amberFilament bulbs, decorative pendants
2700K warm whiteAn old filament bulbLiving rooms, bedrooms, lamps
3000K warm whiteHalogen, slightly crisperKitchens, bathrooms, hallways
4000K cool whiteNeutral, clear whiteUtility rooms, garages, workspaces
5000K to 6500K daylightBlue-whiteCraft or task lamps; usually too stark for living spaces

Keep to one colour temperature in a room. If a bulb also lists CRI, 80 or above is standard and 90 or above shows food, skin and fabrics more naturally.

Step 5: dimmable or not

If the light is on a dimmer switch, buy bulbs marked dimmable. Non-dimmable LEDs on a dimmer will flicker or fail early. Even dimmable LEDs need a dimmer that suits them, usually a trailing-edge type, and enough bulbs to meet the dimmer's minimum load. Our LED lighting guide explains the details. Buy the same make of bulb for every lamp on one dimmer so they dim evenly.

Bulbs and shades

  • Never exceed the maximum wattage printed on a fitting or shade. LED makes this easy, but the limit still applies.
  • In fully enclosed fittings, choose bulbs the maker says suit enclosed use; heat shortens LED life.
  • With an open-bottom lamp shade, a frosted or opal bulb avoids a bright spot when seen from below.
  • Clear crystal and glass fittings, like many in our crystal lighting and chandeliers, sparkle more with clear bulbs.

Before you order

  • Read the cap off the old bulb or the fitting: E27, E14, B22, B15, G9, GU10 or GU5.3.
  • Check the shape and size will fit the shade or glass.
  • Match the lumens to the bulb you are replacing.
  • Pick the colour temperature already used in the room.
  • Choose dimmable if the light is on a dimmer.
  • Count how many you need: a five-arm chandelier needs five matching bulbs.

Browse our bulbs and accessories, or find the bulb offered on the product page of the light you are buying, whether it is a pendant, a table lamp or a set of spotlights.

Need a hand choosing?

If you are not sure which bulb, dimmer or fitting you need, call our advice line on 01422 363525. Better still, bring the old bulb or a photo of the fitting into our Halifax showroom or Bradford showroom (Bradford line 01274 731333) and we will match it. You can also book an appointment if you want time to talk a scheme through.

Questions people ask

What is the difference between E27 and B22?

E27 is a 27 mm screw cap (Edison screw); B22 is a 22 mm bayonet cap that pushes in and twists. They are not interchangeable, so check which your lampholder takes.

What is a G9 bulb?

A small mains-voltage capsule bulb with two looped pins 9 mm apart, used in many modern ceiling lights, wall lights and glass fittings. LED G9s are slightly larger than old halogen ones, so check they fit inside any glass cover.

Can I replace GU10 halogen spotlights with LED?

Yes, GU10 LEDs fit straight in. Compare lumens and beam angle with the old bulbs, and if the spotlights are on a dimmer, choose dimmable bulbs and check the dimmer suits LED.

How do I tell GU10 from MR16?

GU10 pins have small feet and twist in; MR16 (GU5.3) pins are thin and straight and push in. MR16 runs at 12 volts from a transformer, GU10 runs on mains.

Which bulb gives the most natural light?

Look for a high colour rendering index (CRI 90 or above) at 3000K to 4000K. For a warm, homely feel, 2700K at CRI 90 is a good compromise.

What bulb does my new light need?

It is listed in the light's specification, and where the light takes a separate bulb we offer the right one on the product page. If in doubt, call us on 01422 363525.

Related guides